When snowshowing, having a backpack with you is always a good idea. You’ll need something to carry your snowshoes in, as well as any other day-to-day items that make life easier on the trail. But attaching your shoes may seem like an impossible task! We’re here today to help you figure out How To Attach Snowshoes To Backpack this can be done.
There are a few different ways to attach your snowshoes, but most will use the same basic process. So let’s look at each approach:
Back-Lacing.
The first method is what’s known as “back-lacing.” This involves tying your shoe laces into a loop and tying the loop to your belt or pack. You might notice that there are many different styles of lacing systems- construction, knotting, etc.- but they all relevantly fall under this category. I prefer a simple “Old Geezer” type of method (see below) so you can see how it works, but back-lacing is never a bad option. It works well on most snowshoes and is fairly easy to learn how to do.
Features: The big benefit of back-lacing is the ease of use. It’s pretty easy to find a spot on your pack or belt and find a way to tie the laces–so this is one of the methods you may want to try first. However, you may find it difficult to put your pack on and take it off if you are wearing your snowshoes with your pack; sometimes, back-lacing will make it awkward or slow down the process of putting your shoes on. But that’s the only drawback here since this option is usually pretty fast and easy once you have the knots tied.
Materials needed: Lace and something to tie it to–usually a belt or pack, but any string material will do. It helps if the lacing is pretty thin and has some flexibility.
How To: First, locate the hole in your snowshoe where the lace goes. Depending on your shoe, there may be more than one of these holes. You want to make sure that you pick one near the top of the shoe (the heel) so you can tighten it enough when you are done.
Next, take your laces and tie them together into a loop. Tie your loops to the back of your belt or pack. This will be where you set your snowshoes for the day. You will adjust them occasionally when you stop along the trail, but for most of your hike, you want both shoes tied together to make sure they don’t slide around too much on the trail.
Note: This method won’t work well if your laces are particularly thick, as it will be hard to find a place to attach them. They should have some flexibility and be thin but not too worn out. Otherwise, you may want to try another method.
Snowshoe Bungee.
The next option is called the “bungee.” You can do this in a couple of ways with different materials. The easiest way is to use one of the cords with your snowshoes (usually red or orange). These have a little elastic, so you can use them to cinch up your shoes.
The first step is to find the hole where one of these cords goes. This is usually near the heel or toe of your shoe. Next, loop the cord around one of your shoes, pull it back through, and tie it off with another knot. This will give you a double loop that holds your shoe in place. Do this for both shoes, and you are all set!
Materials needed: A bungee cord (usually on snowshoes), string or rope, a lighter, and a needle if using the rope.
How To: The process is pretty simple. Take your cord and find the hole closest to your shoe’s heel (usually about one-third of the way up). Place this cord over one of your shoes (it doesn’t matter which one) and loop it underneath itself. Pull it all the way through, tuck under itself again, and tie a knot.
Now do the same thing on the second shoe with the other cord. This should give you two loops in each shoe-both placed near their heels on both shoes-to hold them in place during use.
Features: This method is simple. It’s easy to attach, durable, and stays in place quite well on your shoe. And best of all, it does not require any stitching or complicated knotting that many other methods need.
Materials needed: Two heavy-duty cords (usually red or orange) tied as shown to the inside of the boot/sock.
How To: This is pretty self-explanatory. You follow the same steps you did above but with a different cord. Find the hole closest to the heel on both shoes for the second cord and place it through. Then loop it over itself, then back under it again–but keep pulling it to the bottom of your shoe! Put a knot in at this point.
You’re done! There’s not much more to explain. You should finish just by pulling your cord tight enough so that both shoes are securely tied in place.
Things to watch out for: The bungee cords themselves can wear out since they tend to stretch with use–something you may want to avoid if possible.
FAQ:
How do you pack snowshoes in a bag?
Be sure to check the shoe for any holes or tears and try to locate any burrs that might make them difficult for you to stand on.
Pack your snowshoes in a case or bag. This will make it much easier to carry and protect them from all the things that will happen with your gear. If you are only going to be out for a short time, it is unnecessary to pack the whole thing in one bag.
If you are going on a trip, try to pack the snowshoe with other items in similar bags. This will help you avoid having too many bags and keep things organized when you head out the door.
When packing the case or bag, use straps to keep it secure. You can also use bungee cords to tighten the straps and ensure the snowshoes stay. It is important to pack them tightly enough so that they will not fall out of your pack, but not so tight that you have a hard time removing them when you need them.
Before you go to the store, it is worth looking at how much room there is in your bag and snowshoe case.
How do you strap snowshoes?
First, make sure that you’re wearing snow shoes that fit properly. It’s very important to have snow shoes that fit properly. Otherwise, your stride will be affected, and you won’t be able to move effectively.
Make sure you have a snug fit and buy a pair of snow shoes from a reputable manufacturer. When buying your snowshoes, you need to consider the different styles, such as cross country and backcountry, but even more importantly, you should look at the shoe size. Snow depth is another important factor affecting your ability to walk in the snow safely.
How do you pack MSR snowshoes?
You should first remember that snowshoes are quite delicate and extremely lightweight. So make sure that every gear you bring is small enough to fit in your backpack. Avoid bringing too many heavy things, such as the last season’s snowshoes. Also, never hang your snowshoes on a tree branch or pole. That can cause injury to the rope and break the hinges of the poles and straps.
You may find it helpful to have a small sack or bag where you can roll your snowshoes up and keep them. You should also leave room for the poles so they will not bend when you put your snowshoes on. Generally, no more than two snowshoe-makers should be allowed to fit in each backpack.
What is the metal bar on snowshoes for?
The metal bar at the front of your snowshoes provides traction and helps you stay upright. The bars also keep your feet from slipping out as you walk through soft snow and allow water and other materials that may have fallen from trees to pass through so your shoes don’t get clogged up. They’re especially good when crossing streams or rivers on streams with thin ice.
Final words:
Whether you are looking for instructions on how to put together a pair of snowshoes from your closet, or you need to know the basics on how to attach snowshoes to backpack, we hope that this post will be helpful for you.
We tried to include as many details as possible that should get you off on the right foot when embarking on your next outdoor adventure. Our hope is that you enjoy your outdoor activity safely and get all of the enjoyment out of it that you expect. Good luck!
